- Pk Ripper Parts
- Pk Ripper Bmx Serial Numbers
- Vintage Pk Ripper
- Pk Ripper 29
- Pk Ripper Frame For Sale
- Original Pk Ripper
When buying any used Harley-Davidson, checking the Harley VIN numbers against the title is mandatory. If they do not match exactly you should think about looking elsewhere. Typographical errors on motorcycle registrations are sometimes very common, but don’t take any chances. In some cases a visit to your local department of motor vehicles may be enough to get a VIN typo corrected. However, when buying a Harley or other vehicle with an out of state title, the difficulty in correcting such errors increases dramatically. With strict state regulations increasing every year, you are better off avoiding any problem that may leave you holding a piece of property that cannot be documented. Not only is it illegal to drive, but you leave yourself open to unscrupulous people who could make a legal claim against you and your property.
If you have a Harley engine with matching title taken from a crashed or salvaged motorcycle, and put that engine into a new frame, the title is invalid. Anyone trying to sell you a post-1970 Harley where the title VIN only matches the engine, but does not match the number on the frame, PASS! Want to upgrade your bike to a new custom frame? You must apply for a new title. While it is nice to have an original Harley with matching engine and frame numbers, only the frame VIN is relevant when it comes to legal registration.
Odds of winning the prize depend upon the number of eligible entries received throughout the Promotional Period. Prize may not be transferred, assigned, redeemed for cash or substituted, except that Sponsor may substitute any prize with a prize of equal or greater value in the event the stated prize becomes unavailable. SE Bikes Newsletter. This is a 1980 PK Ripper looptail frame.Serial number is PK36673. I am no expert when it comes to bicycle frames and am selling this frame for my brother in law. Frame is in good condition with some scratches and scuffs.No big dents but a few nicks.There is some minor damage.
Ltd Numbered 2007 SE Quadangle 30th Anniv. Looptail Frame BMX Pk Ripper STR1. Condition is New. Limited, Numbered 2007 SE Quadangle Looptail Frame. This is low serial. If you search for 1234, you will only find bikes with serial numbers of 1234 and serials close to that - not a bike with serial number of 12345689. Okay, fine, so maybe there are a few bikes without serial numbers, but this is rare and typical only on hand made bikes or really old bicycles. During the 1979 model run, some Harley’s were produced with engine numbers that did not match the frame number. The production date is reported to be from 1/9/79 – 2/7/79, and the frame VIN’s affected are 43000H9 through 48199H9. These models had engines numbered with a separate “crankcase number” instead of the frame’s VIN.
Never accept a Harley or other vehicles without a legal title. One such case involved an individual restoring a Harley originally purchased without proper papers. Some deadbeat and his lawyer came along and claimed the Harley was his. Without enough money to pay an attorney, and lacking any legal title or receipts, the poor guy was forced to give the bike to this shark in order to avoid a lawsuit. This may sound like extortion but it happens all the time. Don’t become another horror story. Take precautions when investigating the authenticity of the Harley VIN and registration.
There has always been much debate over bikes with matching numbers and their true value. In my opinion, any Harley being sold as “rare” or “limited” is usually anything but that. As with beauty, value and rarity are often in the eye of the beholder. If matching numbers makes a motorcycle more valuable to you, then only you can put a value on it. Just don’t expect the next person buying that Harley from you to think the same way.
Locating the Harley VIN
Prior to 1961 On Harley models prior to 1961, the engine number acts as the VIN. This number can be found on the left side engine case. Harley models produced prior to 1969 do not carry any frame number. VIN Numbering Conventions:
- First two numbers are the model year.
- Letters (up to four) are the model designation.
- The last numbers are the production run number.
1962 – 1969
VIN Numbering Conventions:
- First two numbers are the model year.
- Letters (2-4) are the model designation.
- The last numbers are the production run number.
In addition, models with 4 digit production numbers have an even-numbered first digit for even years, odd for odd years. Models containing a 5 digit production number will have the first two digits even for even years, odd for odd years.
Why is this important? If the VIN does not follow this even or odd numbering sequence, you can almost guarantee that the VIN has been altered. It is extremely common to find mismatched engines in these early bikes with different VIN numbers than the title paperwork. 1970 – 1980:
Beginning in 1970, Harley started stamping VIN numbers on both the frame and engine case. The exception as noted by our friends at Cyborg Cycles, is the 1979 model . This exception is discussed below.
- First two numbers are the model code.
- Next 5 digits, position 3-7 is the production run number.
- The last 2 digits designate the year.
The only legal VIN number for Harley’s produced after 1970 is on the frame. NO EXCEPTION! It doesn’t matter if the engine case number matches your registration papers, if the frame VIN doesn’t match the registration you have a problem! You might be able to fool a few cops or even someone at the DMV, but don’t count on it. In addition, it should go without saying that any alteration to the VIN is illegal. This goes for restamping frames or adding the original VIN to a replacement frame. If you replace the frame, you need to have a new VIN assigned to your Harley.
Always remember that on models built after 1970, the Harley VIN always follows the frame… not the engine!
The infamous 1979 Exception
During the 1979 model run, some Harley’s were produced with engine numbers that did not match the frame number. The production date is reported to be from 1/9/79 – 2/7/79, and the frame VIN’s affected are 43000H9 through 48199H9. These models had engines numbered with a separate “crankcase number” instead of the frame’s VIN. This engine number is reported to be a ten digit numeric ID. Rumor has it that Harley went back to the old numbering sequence once the legal ramifications were realized. Regardless of the engine case number, the title must always match the frame VIN. Thanks to Cyborg Cycles for this information.
1981 -2000:
Beginning in 1981, Harley started using a 17 digit VIN number on the frame and an abbreviated VIN on the engine case. As always, the legal title must match the VIN number on the frame. If the title and frame VIN reads 1HD1ELK12BZ123456 , the engine case number should read something like ELKB123456 . VIN number rules described under the 1970 – 1980 Harley models also apply here.
Harley VIN Model Year Designations
Prior to 1970 the model year appeared in the last 2 digits of the Harley VIN. From 1970 to 1980 Harley used an alphanumeric year code. The code “H” is followed by the last number of the year (i.e. 1971= H1, 1972= H2). The exception is 1980 which was J0.
1981 to 2000 model big twins Single letter in the 10th digit designates the model year.
| 1981 – B | 1986 – G | 1991 – M | 1996 – T |
| 1982 – C | 1987 – H | 1992 – N | 1997 – V |
| 1983 – D | 1988 – J | 1993 – P | 1998 – W |
| 1984 – E | 1989 – K | 1994 – R | 1999 – X |
| 1985 – F | 1990 – L | 1995 – S | 2000 – Y |
Harley VIN Model Codes
Big Twins
As if things weren’t confusing enough, Big Twin’s have a different set of model designations in the Harley VIN depending on whether they are a 4 speed or 5 speed model. 1970 thru 1980 4 Speed Big Twin The first 2 digits of the Harley big twin’s VIN digits are the model code.| 1A = FL/FLP 1200 | 2F = FXS 1200 | 5H = FLHS – 80 | 7H = FLH 1200 Police |
| 1H = FXB – 80 | 2H = CLE – 80 | 6E = FXEF – 80 | 8H = FLH 1200 Shrine |
| 1K = FLH – 80 shrine | 3G = FLH – 80 | 6G = FXE – 80 | 9D = FXE 1200 |
| 2A = FLH 1200 | 3H = FLH – 80 Classic | 6H = FL – 80 | 9G = FXWG – 80 |
| 2C = FX 1200 | 5E = FXEF 1200 | 7G = FXS – 80 | 9H = FLH – 80 Police |
Example: 3G 12345H1 is an FLH
1980 5 Speed Big Twin
Harley 1980 5 Speed’s used code 5G
1981 thru 1985 4 Speed Big Twin The 5th and 6th digits designate the model code.| AA = FLH – 80 | AL = FLH – 80 | BE = FXWG – 80 |
| AB = 80 police chain | BA = FXE – 80 | BF = FXSB – 80 |
| AC = FLH – 80 Shrine chain | BB = FXEF – 80 | BH = FXST |
| AH = FLHP – 80 Police Belt | BC = FXS – 80 | BG = FXDG – 80 |
| AK = FLHS – 80 | BD = FXB – 80 | BK = FXSTC |
Example: 1HD1 BE K11BY123456 is a FXWG 1981 5 Speed Harley Big Twin The 5th and 6th digits designate the model code.
Pk Ripper Parts
| AE= FLT | AF= FLTC |
Example: 1HD1 AF K11BY123456 is a FLTC 1982 thru 2002 5 Speed Big Twins The 5th and 6th digits designate the model code.
| BH = FXST | DJ = FLHTC | FE = FLTCU-I |
| BJ = FLSTC | DK = FLTC Shrine | FF = FLHTC-I |
| BK = FXSTC | DM = FLTCU | FG = FLHTCU-I W/SC |
| BL = FXSTS | DP = FLHTCU | FH = FLHP-I Police |
| BM = FLSTF | EA = FXR | FJ = FLHP Police |
| BN = FLSTN | EB = FXRS | FL = FLHTCU-I Shrine |
| BP = FXSTSB | EC = FXRT | FM = FLHTP-I Police |
| BR = FLSTS | ED = FXRP Police windshield | FP = FLTR |
| BS = FXSTD | EF = FXRP Police Fairing | FR = FLHRC-I |
| BT = FXSTB | EG = FXRS-SP | FS = FLTR-I |
| DA = FLT 82 – 83 | EH = FXRD | FT = FLHPE-I (California) |
| DA = FLHTP Police Windshield | EJ = FXRC | GA = FXDB-D |
| DB = FLTC | EK = FXRP Police C.H.P. | GB = FXDB-S |
| DC = FLHT | EL = FXLR | GC = FXDC |
| DD = FLHT | EM = FXLR Conv | GD = FXDL |
| DE = FLHTC W/sidecar | FA = FLHS | GE = FXDWG |
| DF = FLHTP Police Fairing | FB = FLHR-I | GG = FXDS Conv |
| DG = FLHTC Shrine | FC = FLHTCU-I | GH = FXD |
| DH = FLTC W/sidecar | FD = FLHR | SG = TLE Police |
| SH = RLE Police |
Sportster VIN Numbers
1970 thru 1980 Sportsters First two digits of the Harley VIN are the model code.| 3A = XL or XLH | 4A = XLCH | 4E =- XLS |
| 2G = XLT | 4D = XLA | 7F = XLCR |
Example:
Pk Ripper Bmx Serial Numbers
4A 12345H1 is a XLCH 1981 to 1985 SportstersVintage Pk Ripper
5th and 6th digits are the model code.| CA = XLH | CB = XLS | CC = XLX | CD = XR1000 |
Example: 1HD1 CD HY15B123456 is a XR1000 1986 to 1996 Sportsters 5th, 6th and 7th digits are the model code.
| CAM = XLH883 | CAN = XLH1100 | CEM = XLH883 Hugger |
| CAP = XLH1200 | CGP = 1200 Custom | CFM = XLH883 Deluxe |
| CHP = 1200 Sport | ||
Example:1HD1 CEM 15GY123456 is a XLH883 Hugger
Confused yet? See Model Number page for a description of Harley model numbers.
Enjoy the ride!
Pk Ripper 29
Note that the information provided here is the intellectual property of Harley-Performance.com and may not be reproduced or distributed without the express written permission of the owner. Models covered do not include late models after 2009.
SE Racing PK Ripper Landing Gear – Details
SE Racing PK Ripper frame and Landing Gear forks. This is an alloy 20 inch loop tail BMX frame with floval tubing. Finished in raw aluminium and with a ball burnished finished although it has also been polished. The black marks around the welds are the remainder of the polishing compounds and not black paint. At least with this frame you can see all the marks and nothing is hidden under paint or powder.
Usual marks and scrapes for a frame of this age. With a bit of work and some we and dry paper, many of these could be removed. I don’t have the patience at the moment. There is a small crack at the end of the slot in the seat post tube. Not an uncommon problem with these frame. The area behind the bottom bracket doesn’t have any cranks.
Dropouts have washer marks and there is a bit of chain rub on the right side.
Landing Gear forks have been re-chromed. Dropouts are in good condition, as are the steerer tube threads.
Serial number on the frame is PK64041.
The PK Ripper sticker on the down tube is a cheap reproduction and really should be removed.
Pk Ripper Frame For Sale
Scroll down for more photos.